A vocal preset is a saved chain of plugins, such as EQ, compression, de-essing and reverb, that you load onto a vocal track in one click. For a beginner, it is the fastest way to get a vocal that sounds finished in Logic Pro X or GarageBand. Load one, then adjust four settings to fit your voice.
The values below are starting points. Your voice, mic and room will change them, so adjust by ear.
What is a vocal preset?
A preset saves the plugin order and every knob setting from a finished vocal chain. When you load it, your track gets the same chain. You do not need to know which plugin goes first or where to set the threshold. You hear a good result first, then learn why it works.
A typical chain has five parts:
- EQ: removes low rumble and muddy tones, and adds clarity.
- Compressor: evens out loud and quiet words.
- De-esser: softens harsh "s" and "t" sounds.
- Reverb and delay: add space around the voice.
- Saturation or limiter: adds warmth and controls peaks.
How do I load a vocal preset in Logic Pro X?
- Record your vocal on an audio track. Keep peaks around -12 to -6 dBFS.
- Click the channel strip name, or open the Library with the Y key.
- Choose the preset from the Library list, or load it from the channel strip's setting menu.
- Play the chorus. Switch the whole chain on and off to hear what it does.
In GarageBand, select the track and open the Smart Controls. Pick the preset in the Library on the left. The steps are the same.
Want the chain already built?
A Thir13een preset loads the whole vocal chain for you, so you start with a polished sound instead of a blank channel strip. Browse the vocal presets for Logic Pro X and GarageBand and pick the style closest to your song. Need help loading one? Read how to install Logic Pro vocal presets.
What should I adjust after loading a preset?
A preset is a starting point, not a final mix. Your voice is different from the voice it was built on. Change these four things first.
- Input level: if the compressor shows more than 6 dB of gain reduction, lower the track gain or raise the compressor threshold. Aim for 2 to 4 dB.
- High-pass filter: set it between 80 and 120 Hz. Raise it if you hear room rumble.
- De-esser: if "s" sounds still bite, reduce 2 to 4 dB around 5 to 8 kHz.
- Reverb amount: turn it down until you only notice it when you mute it. Beginners almost always use too much.
Why does my preset sound different from the demo?
Three things cause this: the recording, the level and the beat.
- A noisy or echoey room shows up more after compression. Record close to the mic, in a room with soft furniture.
- A vocal that is too quiet or too loud hits the compressor wrong. Fix the level first.
- The vocal must sit with your beat. Mix it with the instrumental playing, not solo.
| Step | What to do | Starting value |
|---|---|---|
| Record | Clean take, close to the mic | Peaks -12 to -6 dBFS |
| Load | Open the Library, pick the preset | Toggle on and off to compare |
| Compression | Check gain reduction | 2 to 4 dB |
| High-pass | Cut low rumble | 80 to 120 Hz |
| De-esser | Soften harsh "s" | 2 to 4 dB at 5 to 8 kHz |
| Reverb | Lower the amount | Barely heard until muted |
Are vocal presets worth it for a beginner?
Yes, if you treat them as a teacher. A preset shows you a working chain, and each plugin you open teaches you a real setting. Read are vocal presets worth it? for the full answer. A preset cannot fix a poor recording, so record well first.
Try a free preset first
Not ready to buy? Start with a free one. See the top 10 free vocal presets, load one on your vocal and use the steps above. When you want more styles, browse the vocal presets collection.
FAQ
Do I need a vocal preset to mix vocals?
No. You can build a chain by hand. A preset saves time and shows you good starting settings, which helps a beginner learn faster.
Do vocal presets work in GarageBand?
Yes. Thir13een sells presets for both Logic Pro X and GarageBand. Check the product page to confirm the version you need before you buy.
Why does my vocal still sound bad with a preset?
Most often the cause is the recording or the level. Re-record closer to the mic, set peaks around -12 to -6 dBFS, then adjust the compressor and reverb amount.


