Shop presets

How to Remove Vocal Noise in GarageBand

GarageBand vocal presets. Add a 2nd preset for 50% off in the cart.GarageBand vocal presets. GarageBand deal: buy 1 preset, get 1 FREE.

To remove vocal noise in GarageBand, add the Noise Gate plugin to the vocal track and raise its threshold until the gaps between words go silent. Then cut low rumble with a high-pass filter in Channel EQ. Fix the noise at the source first, because no plugin removes hiss from a loud, clipped recording cleanly.

How do I remove background noise from a vocal in GarageBand?

Use three tools in this order: a clean recording, a Noise Gate, and a high-pass filter. The gate silences the track when you are not singing. The high-pass filter removes low rumble from air conditioning, traffic and desk bumps. Together they handle most home-studio noise. Steps 1 to 4 below show each setting.

Step by step: how do I clean up a noisy vocal in GarageBand?

  1. Record at a healthy level. Sing at your normal volume, a few inches from the mic, and watch the track level meter. Aim for peaks that stay in the green and never touch red. A quiet recording forces you to turn it up later, and that lifts the noise with it.
  2. Add the Noise Gate. Select the vocal track and open Smart Controls and go to the Plug-ins section. Add the Noise Gate plugin. Raise the threshold slowly while you play a part with pauses. Stop when the hiss between phrases disappears but the ends of words still ring out. If word endings get chopped, lower the threshold a little.

Want the gate and the rest of the chain already set up?

The Hip-Hop Vocal Preset Bundle for GarageBand loads a ready-made vocal chain on your track in one click. You can then adjust the gate and the other settings by ear for your mic and your room.

  1. Cut the rumble with a high-pass filter. Add Channel EQ to the track and switch on the high-pass filter. Start around 80 Hz and sweep up until the low thump fades. Stop before the voice sounds thin. For most voices, 80 to 120 Hz is a safe zone. Our GarageBand vocal EQ settings guide covers the rest of the EQ.
  2. Add the Compressor last. A compressor makes quiet sounds louder, and that includes noise. Put the Compressor after the gate and the EQ in the plugin order, and use gentle settings. If the noise comes back after compression, lower the gate threshold or re-record closer to the mic.

Why does my GarageBand vocal sound hissy or fuzzy?

Hiss usually comes from a low input level, a long cable run, a noisy room or a mic placed too far away. Fix these before you reach for plugins. Turn off fans, close the window, move away from the computer, and record closer to the mic. A phone-quality room needs soft surfaces nearby, such as a duvet or a coat rack behind you.

Why does the noise gate cut off my words?

The threshold is set too high. The gate closes when the signal drops under the threshold, and soft word endings drop under it first. Lower the threshold in small steps until the endings return. If the gate still chatters, record at a higher level so the voice sits further above the noise.

Can I remove noise from a recording that is already done?

Partly. The Noise Gate and high-pass filter work on any recorded track. They cannot remove noise that sits at the same moment as your voice, such as a hum under every word. For that, re-record in a quieter spot. If the vocal is also too soft after cleaning, see why GarageBand vocals sound too quiet.

What should I do after the noise is gone?

Shape the tone and add space. Our guide to GarageBand vocal effects explains echo and reverb, and you can browse more GarageBand vocal presets for a finished chain. Want to hear a full chain on your own voice first? Download a free preset from the free vocal presets collection.

FAQ

Does GarageBand have a noise reduction plugin?

GarageBand has a Noise Gate plugin, which silences a track below a set level. It is the main built-in tool for vocal noise. It works best between phrases, not under the voice.

Where is the Noise Gate in GarageBand?

Select the track, open the Smart Controls, and find the Plug-ins section. Add Noise Gate from the plugin list, then set the threshold by ear.

What high-pass frequency should I use on vocals?

Start near 80 Hz and raise it until the rumble fades. Most voices sound fine up to about 120 Hz. Go higher only if the voice still sounds clear.

Should I put the gate before or after the compressor?

Before. The gate removes noise first, so the compressor does not lift it. Put EQ in between if you want, then the compressor.

Voltar ao blog

Deixe um comentário

Presets Vocais para Logic Pro X